Kitchen & bespoke joinery spraying

A careful process for a beautiful finish.

From the first surface check to the final refit, each stage is planned around the material, existing finish and the home we’re working in. Here’s how we approach a kitchen or fitted joinery spray project.

The process

How We Refinish Your Kitchen

Once we’ve agreed on your chosen colours and the scope of work, we follow a carefully planned, step-by-step process to deliver a consistent, high-quality finish.

01

Before we start

We assess the surfaces to be sprayed, including whether they have been previously painted, varnished or wrapped. We check their condition, identify any repairs or staining, and determine how much cleaning is needed—particularly for kitchen cabinetry. We also assess the work area, including the masking required, where equipment can be set up and the ventilation needed. This allows us to plan the preparation properly and provide a fair, accurate quote based on the work required to achieve a high-quality finish.

02

Clean before preparation

For kitchen cabinet projects, we begin by thoroughly cleaning and degreasing the surfaces using specialist products and suitable tools. This removes the grease and grime that build up through years of everyday use. We also vacuum the work area and clear away dust and cobwebs, leaving everything clean and ready for the next stages. This is an essential step in achieving a consistent, high-quality finish.

03

Dismantle and label all components

Doors and drawer fronts are carefully removed and numbered inside the hinge recesses. Each corresponding cabinet and drawer is given the same number so every component can be returned to its original position. Hinges, drawer runners and other removable hardware are labelled and stored in numbered, resealable bags. We mark hinges as top or bottom, and keep handles with their components unless they are being replaced. The labelled doors and drawer fronts are kept together in numerical order, ready to be placed on the drying rack once it has been set up.

04

Masking

Before work begins, we protect the surrounding area. Floors and worktops are covered with Q1 floor protection, a lightweight protective card. Nearby walls are shielded with plastic sheeting secured with sensitive-surface tape, helping to reduce the risk of lifting paint when the tape is removed. Depending on the kitchen layout and unit height, we may protect sections of the ceiling in the same way. Plug sockets, fixtures, tiled splashbacks, the sink and nearby appliances are carefully masked. Where safe and practical, we arrange the protection so the sink and appliances remain accessible. Some may need to be temporarily kept out of use during sanding or spraying.

05

Set up the spray booth and drying rack

For kitchen resprays, we use a ZipWall system to create a contained work area. Adjustable poles are secured from floor to ceiling and support durable plastic sheeting, allowing us to section off the main kitchen before spraying begins.

We position our PaintLine drying rack away from the kitchen work area. Once the rack is in position, we hang the numbered doors and drawer fronts on it to dry. We then assemble the spray rack and build a dedicated booth around it.

A heavy-duty extraction fan, fitted with a filter and connected to an exhaust hose, draws overspray out of the booth and vents it outdoors through a suitable window or doorway. This helps control airborne paint and keep the surrounding area cleaner during spraying. Access to the contained spray area is restricted while spraying is underway.

06

Sanding

We begin by sanding the surfaces using Festool and Mirka sanders connected to a Festool dust extractor. Large areas are machine sanded, typically starting with 120-grit abrasive and working up to 240 grit, depending on the surface. This helps remove roughness, create an even base and provide a suitable key for the coating to adhere to.

Detailed areas that the sanders cannot reach are finished by hand using Mirka Goldflex sanding pads. Once sanding is complete, we vacuum away the dust and carefully wipe the surfaces with tack cloths or clean microfibre cloths to remove any remaining particles.

Between each coat, we lightly hand-sand the surface with 320-grit abrasive. This helps maintain a smooth finish and remove minor imperfections before the next coat is applied.

07

Filling and Repairs

Once sanding is complete, we assess the surfaces and carry out any necessary filling and repairs. For more substantial timber damage, we use Repair Care, a specialist resin system designed for wood repairs. It can be shaped to recreate missing profiles and contours, helping us achieve a durable repair that blends with the surrounding surface.

When clients choose to replace existing kitchen handles or knobs, we use resin to fill the original fixing holes. This provides a solid, well-prepared surface for fitting the new hardware securely.

We inspect each surface under good lighting to identify small defects and areas of damage. Depending on the substrate, depth of the repair and required curing time, we select the most suitable wood filler. Once the filler or resin has cured in line with its product guidance, we sand the repaired areas flush with the surrounding surface and remove the resulting dust before priming. After the final primer coat, we inspect the surfaces again and address any remaining imperfections before applying the finish coats.

08

Spraying the primer

With preparation complete, we apply Sayerlack’s professional waterborne coating system, selected for kitchen cabinetry.

We use AU0474/13 to create a consistent base with good coverage, filling properties and a smooth surface that is easy to sand. Previously uncoated timber receives two coats; sound, previously painted surfaces typically receive one, depending on their condition and the coating system.

We spray the fixed kitchen units first, followed by the doors, drawer fronts and any other removed components. Once the primer is dry and ready for sanding, we inspect each surface under good lighting, checking coverage and identifying any imperfections to address before applying the topcoat. We then lightly sand the primer to create an even base and remove minor surface imperfections, before vacuuming and wiping away the sanding dust.

09

Applying the final coating

We finish the kitchen with Sayerlack AT99, a one-pack waterborne topcoat for interior wood. It provides excellent surface hardness and good chemical resistance, with good vertical hold, flow and wetting to support an even, smooth finish on the units and components.

AT99 is available in 5%, 15%, 30% and 50% sheen levels, from a very matt appearance to a higher sheen. The 15% sheen finish is our most popular choice for a soft, low-sheen look.

We follow Sayerlack’s product guidance for drying and recoat times, which can vary with conditions on site. We spray the first topcoat over the kitchen units and removed components. Once dry, we inspect the surfaces and lightly hand-sand with Mirka Goldflex 400-grit abrasive to smooth any minor imperfections. After removing the sanding dust, we apply the final sprayed coat to complete the finish.

10

Final inspection

Once the final coating has been applied, we inspect every sprayed component and fixed surface using a detail light. We check for even coverage, a consistent sheen, a smooth finish and any missed areas or minor imperfections. We also confirm that repaired and filled areas are properly covered and that edges, corners and detailed sections have received an even finish.

If anything needs attention, we address it before the components move on to curing and refitting.

11

Refit the kitchen

Before refitting, we allow the coating to reach the handling stage recommended in the product guidance, taking site conditions into account. We wear powder-free latex gloves while refitting each door, drawer front and removed component. This helps protect the finish from fingerprints and skin oils while it continues to cure.

Using our labels, we return each component to its original position and reinstall the original handles where they have been retained. If you’d like new handles fitted, we can include this at an additional cost, agreed with you during the quotation stage.

We then check that the doors and drawers are aligned, open and close smoothly, and that all refitted hardware is secure.

12

Remove protection and clean

Once the kitchen components have been refitted, we carefully remove the masking tape, plastic sheeting and floor protection. We then dismantle the ZipWall partition and spray booth, and pack away the drying rack and equipment so the work area is clear.

To finish, we vacuum the floors and wipe down the worktops and appliance exteriors within the work area. We remove the remaining protective materials and waste, leaving the kitchen clean, tidy and ready for handover.

13

Handover and walk-through

Once the kitchen is complete, we carry out a final walk-through with you. We’ll show you the areas that have been repaired and refinished, so you can see the improvements and the care taken with the work.

We’ll review the finished surfaces together and answer any questions. We’ll explain that the coating continues to cure and harden after refitting, and give you product-specific guidance on caring for it. For routine cleaning, we’ll recommend a soft cloth and a suitable mild, non-abrasive cleaner, and advise you to avoid abrasive pads and harsh cleaning products. We recommend taking extra care with the surfaces for the first two weeks.

If you notice anything that needs attention during the walk-through, we’ll discuss it with you and address any agreed adjustments before we leave. Our aim is to hand over a clean, carefully finished kitchen and ensure you’re happy with the result.

The coating system

More about the coatings we use

We use Sayerlack’s 1K waterborne system for kitchen cabinetry and interior joinery. Our primer and topcoat are selected to create an even, durable finish, with each product applied in line with its technical guidance.

01 · Primer1K · Waterborne

AU0474/13

White pigmented spray basecoat

  • High pigment and solids content for strong hiding power and an even colour.
  • Very good filling power to help create a smooth, consistent base.
  • Good sanding properties to prepare the surface for the topcoat.
  • Designed for internal wood surfaces.
  • It provides excellent coverage and a suitable surface ready for the topcoat.
02 · Topcoat1K · Waterborne

AT99

Waterborne interior topcoat with tinting bases

  • Very good surface hardness for a hard-wearing interior finish.
  • Good chemical resistance for everyday interior use.
  • Suitable for vertical spray application.
  • Available in most colours, including Farrow & Ball and Little Greene.
  • Exceptional choice for kitchen cabinets due to its durability, hardness, solid colour and chemical resistance.

Four sheen levels available

5%Sheen
15%Sheen
30%Sheen
50%Sheen

Product performance depends on the substrate, preparation and application conditions.

Beyond the kitchen

The same care for bespoke joinery.

Fitted wardrobes, media walls, alcove units, shelving and other made-to-measure joinery each require a tailored approach. We assess the materials, existing finish and condition, then adapt the cleaning, repairs, sanding and masking to suit the piece.

Where practical, removable components are labelled and taken apart for separate finishing. Fixed joinery and surrounding areas are carefully protected, with a contained spray area set up where needed. We apply a suitable primer and topcoat, sanding between coats as required, then inspect the finish under detail lighting. Finally, we refit the components, remove the protection, clean the work area and walk through the completed work with you.

  • Fitted wardrobes and bedroom furniture
  • Media walls and entertainment units
  • Alcove cabinets and shelving
  • Doors, panels and other interior joinery

Planning a kitchen or joinery respray?

Send us a few photos and your postcode. We’ll talk through the finish, the surfaces and the best next step for your project.

ContentsMenu

Explore Luxe

Call LuxeWhatsApp